You should know the Dayton B652 speakers set a new sound quality standard for under $50 per pair. The B652 rapidly became my go-to speaker for aspiring audiophiles or anybody looking for the finest sound for the least amount of money.
The B652-AIR is not going to win any beauty contests, but it is far from ugly. It resembles the basic speakers that come with home-theater-in-a-box systems. Fiberboard, not plastic, makes up the basic rectangular container.
When tapped with knuckles, it reveals audible resonances, suggesting little (if any) internal bracing or dampening. If you are interested in this model, keep reading our Dayton Audio B652-Air review for more information below.
Dayton Audio B652-Air
About: If you are on a tight budget and need a home theater system right now, these speakers can suffice. Dayton Audio B652-Air is better than the previous models and can offer you an amazing sound and bass at once.
So, how does Dayton Audio B652-Air sound? There are no noticeable rough edges or harshness, and it does not sound like a cheap speaker. For all of my listening tests, I utilized my low-cost Emotiva Mini-X a-100 integrated amplifier (2 x 60 watts).
The dramatic punch of the B652-AIR is impressive, and the sound is well-balanced, neither too bassy or bright according to our Dayton Audio B652-Air review .
Bass went down to approximately 65Hz in my huge space, which is enough for a speaker of this size. If you want more bass, upgrade your speakers or invest in one of Dayton Audio’s affordable subwoofers.
This bookshelf speaker is 11.8 inches (299mm) tall and features a 6.5-inch (165mm) polypropylene woofer, which is significantly bigger than typical cheap speakers. The B652-AIR uses a high-tech air motion transformer tweeter instead of a dome tweeter.
This 1-inch (24.4mm) square flat tweeter offers a cleaner, lower-distortion sound than dome tweeters. Because the B652-AIR’s impedance is 6 ohms, it may be used with receivers that handle 4- to 8-ohm speakers.
According to this Dayton Audio B652-Air review, the B652-AIR is not a replacement for the B652, and both models will be available in the Dayton portfolio.
Pleated planar speakers, or AMTs, are similar to accordion speakers in that they are folded like an accordion and force sound waves out in a square pattern rather than a sphere like a dome.
There are many more details to go into discussing all of the nice things about AMTs, but the bottom line is that they typically sound excellent and can scale up to sizes where they can crossover lower than most other tweeters according to our Dayton Audio B652-Air review.
Because this AMT is one of the tiniest we have ever seen, it will not play very low. This should not be an issue because the B652’s plastic tweeter produces steam at 4500Hz, so it is not a difficult target to reach.
This is the same 6.5-inch poly woofer found in the standard B652. These do not appear to have as much bass as we recall them having, but they appear to accomplish the job in any case according to our Dayton Audio B652-Air review.
As a result of the measuring approach, there will be a natural increase toward the FS of the driver (110Hz) in this near mic test. While this demonstrates a rather well-behaved driver, there is a 3dB spike out at 3150Hz when the driver undergoes break up.
The bass is decent, though a touch light on true bass considering its size. The lower midrange is further weakened by the lack of baffle step correction.
These sound a little bright at the top, a little weak at the bottom, and as if the treble is missing according to our Dayton Audio B652-Air review. The tweeter on the B652s has been replaced with a sound that is not only non-offensive but also bright and sparkly in the upper octaves.
It is almost as if they wanted to be sure you could hear the AMT, so they turned up the volume a bit more than it needed to be. It sounds a lot nicer than the B652, which is exactly the point.
A keyhole mount and a pair of spring-loaded wire clips, the cheapest available speaker terminals, are located on the rear. We do not complain about it though. Pin plugs, bare wire, or the soldered tips of the provided thin cables can all be used with the clips.
If you want to utilize terminated speaker cables, you will have to detach the banana plugs from your other device cables and use the underlying pins, which is exactly what some people did as we have to mention in this Dayton Audio B652-Air review.
What is an ATM?
AMT stands for Air Motion Transformer, a transducer that stands out in the field of speaker drivers as a one-of-a-kind design. A folded Kapton ribbon diaphragm is used in the AMT found in Dayton Audio speakers.
More air can flow through the diaphragm with less effort and distortion as a result of this according to our Dayton Audio B652-Air review. When compared to a typical dome-style tweeter, this results in a more clean and satisfyingly dimensional sound.
Conclusion: Dayton Audio B652-Air [2022 Review]
You can get the same power and punch as the original Dayton Audio B652 speakers, but with the added benefit of AMT (Air Motion Transformer) technology for immaculate high-frequency performance.
The inclusion of a higher-quality AMT tweeter elevates the Dayton Audio B652-AIR speakers to a new level. This feature alone should be why you should buy this speaker model. We hope you liked our Dayton Audio B652-Air review and it was helpful.